盛源彩票开户

行業新聞
當前您的位置:網站首頁 > 行業新聞

生料帶纏繞誤區介紹


發布時間:2019-12-11    編輯:杭州恩立氟塑料制品有限公司    瀏覽次數:312次    標簽:

 SHENGLIAODAIBINGBUSHICHANRAODEYUEDUOMIFENGCAIHAO,SHENGLIAODAICHANDUOSHAOQUANXUYAOGENJULUOWENJIANXIPEIHEERDING。ZAICHANHAOSHENGLIAODAIHOU,YEXUYAOZHUYININGJINDELIDU。GENJUSHIFUFANKUI,XIANYONGSHOUNINGJINLUOWENPEIJIAN,RANHOUZAIYONGGUANQIANNINGJIN0.5-2QUANJIKE。ERXUYAOCHANDUOSHAOQUANHENINGDELIDU,NEIJIUYAOGENJUGUANDAODEBIAOZHUNLE。

纏繞完成后直接用手撕斷即可,這時,我們再將絲扣管件或者螺母擰緊即可,現在廠家生產的生料帶已經在使用上非常的方便了。
生料帶是用來密封管道連接處,使管道的密封性更好,有時候還會用于水暖安裝工程。但很多時候,大家都會說到,纏了十幾圈生料帶的水龍頭,為何還漏水。大部分原因是因為生料帶的纏法弄錯了,
分析:
一:生料帶需要順著螺紋方向纏繞,纏反了密封性能大大下降;
二:千萬不要把所有螺紋都纏上生料帶,除了避免生料帶進入管道,也會降低密封性能。建議從螺紋始端的第二個絲牙開始纏繞,把第一個絲牙留出來;
三:纏繞生料帶時需要稍微用力,保證生料帶不被拉斷的情況下纏繞,這種方式纏出來的生料帶才夠緊致牢固,確保密封性。
Raw material tape is not wrapped more sealed before good, raw material tape wrapped how many rings need to be in accordance with the thread clearance. After wrapping the raw material belt, also needs to pay attention to the tightening strength. According to the feedback from the master, first tighten the thread fittings by hand, and then use the pipe pliers to screw in 0.5-2 turns. And the amount of twisting and twisting required, it depends on the standards of the pipe. After winding, we can tear it by hand. At this time, we can tighten the screw fitting or nut. Now the raw material belt produced by the factory is very convenient to use. Raw material tape is used to seal pipe joints, so that the pipeline is better sealed, sometimes also used in plumbing installation works. But a lot of times, everyone will say, wrapped in a dozen rings of raw material Belt Faucet, why leak. Most of the reasons are due to the wrong way of winding the raw material belt. Analysis: First, the raw material belt needs to be wound in the direction of the thread, and the sealing performance is greatly reduced if it is wound in the opposite direction In addition to avoiding the raw material into the pipeline, will also reduce the sealing performance. It is recommended that the first filament be left out by winding the second filament at the beginning of the thread. 3: The raw material belt needs to be wound with a little force to ensure that the raw material belt is not broken This way the raw material wrapped out of the belt is tight and strong enough to ensure sealing.

上一篇:有油生料帶與無油生料帶有什么區別      下一篇:生料帶的耐溫性能